Your cart
There are no more items in your cart
• PRE-PASTED NON-WOVEN WALLPAPER •
Media concerned: Aquapaper Satin pre-pasted
Control of the decor
The PaperMint teams check your order with the utmost attention before shipping. Nevertheless, in order to avoid any possible mistake, we advise you to check your decor before installation.
The implementation, by you or the installer, engages your responsibility with regard to these products. We do not take back or reimburse a set already installed.
Manufacturing tolerances are 1/1000, i.e. 1 mm per metre. This type of deviation is imperceptible if the strips are correctly centred, so we advise you to check this point before gluing.
If you have any doubt or a quality/SAV request, please send an e-mail to our customer service department: serviceclient@paper-mint.fr
Characteristics
Our decors are high quality products manufactured in France with the greatest care and rigorous quality control, nevertheless a decor printed on paper remains a product to handle with care.
Ecological papers
They are composed of cellulose and polyester. Printed with Latex inks (water-based), they guarantee a healthy interior without pollutants.
Washable
The paper can be washed with a sponge and soapy water, which simply removes the dirt!
Careful
The printing of our different types of paper is protected by a coating that prevents surface moisture from penetrating the thickness of the paper.
It is therefore necessary to avoid excess water, run-off, stagnation or cleaning with a sponge that is too wet.
It is important that the moisture remains on the surface, if the paper is wet in the thickness it must be allowed to dry before rubbing, the risk would be to remove the ink from the paper.
Avoid rubbing too hard or with an abrasive sponge in order not to damage the print.
Also, do not use detergent or solvent to clean the decor. If in doubt about cleaning, contact us.
The surface
Wallpaper adhesives adhere only to porous surfaces, preferably prepared with an undercoat or an old paint. Our papers are covering but it is better to put on a wall painted in a plain way without traces or marks.
Reactivatable glue
Water-based, odorless glue is reactivated by simply spraying water on the wall and the strip, or using a damp sponge.
During this step, be careful not to soak the strips so that the glue does not come off.
Quick and easy to apply
Edge-to-edge installation, does not shrink during drying (high stability). Nevertheless, avoid installing the wallpaper in temperatures above 25°C.
Material
Here are the tools you will need for the installation of non-woven paper to glue:
- Water sprayer
- Bucket
- Sponge
- Sizing brush
- Plumb line or ruler or level
- Pencil
- Tape measure
- Sponge brush (do not use a spatula)
- Roller
- Cutter, scissors
- Step ladder
Installation of the decor
Preparation and control of the panels before installation
Pre-cut strips ready to install
These panels are cut and joined to the dimensions indicated and in the quantities specified on your order. They are generally classified in order (reference of the panels on the back or at the bottom according to production for non-repetitive patterns or particular compositions) and packaged in a single roll.
Check that you have all the panels, that the joints are correct, that the height and other aspects (paper, color, etc.) are in accordance with your request before starting the installation.
Rolls
Paper from rolls, regardless of its length, requires preparation. It is necessary to cut strips adapted to the wall and to manage the connection of the pattern between each strip before the installation.
Check that the rolls conform to your request (length, width, pattern, color, paper type, etc.) before starting the installation.
Installation of the wallpaper
Make sure to center the strips on the wall, do not start with a whole strip if you have to have a small strip at the end of the wall; it is better to distribute the width to be covered between the first and the last strip in order to have a more balanced decoration.
We recommend starting with the second panel for your wall.
Using a plumb line or level, determine the vertical for the first panel, avoiding the wall angle if there is one, as it may not be completely straight.
We recommend marking with a pencil to ensure the verticality of the first panel, but these marks can be seen through the window, so avoid using thick or greasy pencils and check any marks before installation to remove them if necessary.
Using the sprayer or the wet sponge, reactivate the glue on the back of each strip.
The opening time of the glue is shorter than that of the glue to be prepared, so we recommend reactivating the glue only when applying the strip to the wall. Remember to also moisten the wall on which the paper is to be applied.
Lay your first strip, keeping a 5 cm margin in height to prevent possible differences in wall height.
Adjust the strip, and marouflage with a brush or the flat of your hand: marouflage consists in chasing the air bubbles from the center to the edges and obtaining a strip perfectly stuck to the support.
Then repeat the different steps with the following panels.
Cut the excess paper with a ruler and a cutter once the glue is dry (about 24 hours).